HERCULES CHEMICAL CO INC -- CLEAR CUTTING OIL  -- 9150-00N001344
<pre>=====================  Product Identification  =====================

Product ID:CLEAR CUTTING OIL
MSDS Date:01/30/1989
FSC:9150
NIIN:00N001344
=== Responsible Party ===
Company Name:HERCULES CHEMICAL CO INC
Address:29 WEST 38 STREET
City:NEW YORK
State:NY
ZIP:10018-5595
Country:US
Info Phone Num:201-778-5000
Emergency Phone Num:201-778-5000
CAGE:84794
=== Contractor Identification ===
Company Name:HERCULES CHEMICAL CO INC
Address:111 SOUTH STREET(OLD IS 29 W 38 ST)
Box:City:PASSAIC
State:NJ
ZIP:07055-7398
Country:US
Phone:973-778-5000
CAGE:84794

=============  Composition/Information on Ingredients  =============

Ingred Name:MINERAL OIL, PETROLEUM DISTILLATES, HYDROTREATED (SEVERE)
    HEAVY NAPHTHENIC; (PETROLEUM BASED LUBRICATING OILS)
CAS:64742-52-5
RTECS #:PY8035001
OSHA PEL:5MG/M3 OIL MIST(MFR)
ACGIH TLV:5MG/M3 OIL MIST(MFR)

Ingred Name:MINERAL OIL, PETROLEUM DISTILLATES, HYDROTREATED (SEVERE)
    LIGHT NAPHTHENIC; (PETROLEUM BASED LUBRICATING OILS)
CAS:64742-53-6
RTECS #:PY8036001
OSHA PEL:5MG/M3 OIL MIST(MFR)
ACGIH TLV:5MG/M3 OIL MIST(MFR)

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:LOW ORAL/DERMAL TOXICITY. POSSIBLE
    ASPIRATION HAZARD:INDUCED VOMITING MAY CAUSE ASPIRATION INTO LUNGS.
    SKIN:MODERATE IRRITATION, DEFATTING. EYE:MILD TRANSIENT IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:INHAL:VAP INHAL UNDER AMBIENT CNDTNS IS NORMALLY NOT PROB. IF
    OVERCOME BY VAP FROM HOT PROD, IMMED REMOVE TO FRESH AIR, IF NOT
    BRTHG. GET MED ATTN. INGEST:DO NOT INDUCE VOMIT. GET MED ATTN.
    SKIN:FLUSH	W/PLENTY OF SOAP & WATER. EYE:FLUSH W/PLENTY OF WATER
    FOR AT LST 15 MINS OR UNTIL IRRIT SUBSIDES. IF IRRIT PERSISTS, GET
    MED ATTN.

=====================  Fire Fighting Measures  =====================

Flash Point Method:COC
Flash Point:320F,160C
Extinguishing Media:DRY CHEMICAL,FOAM,CARBON DIOXIDE
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
    PROTECTIVE EQUIPMENT . USE WATER TO KEEP FIRE EXPOSED CNTNRS COOL.
    WATER MAY BE USED TO FLUSH SPILLS AWAY FROM EXPOS.
Unusual Fire/Explosion Hazard:NONE

==================  Accidental Release Measures  ==================

Spill Release Procedures:HANDLE AS AN OIL SPILL. USE OIL ABSORBING
    MATERIAL. SWEEP & SCOOP UP & REMOVE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:NO SPECIAL PRECAUTIONS MEEDED
    NORMALLY. HOWEVER,AVOID BREATHING OF OIL MIST & EXCESSIVE SKIN
    CONTACT.
Other Precautions:MINIMIZE BREATHING VAPOR, MIST, FUMES.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NIOSH/MSHA APPROVED MASK FOR OIL MIST.
Ventilation:LOCAL EXHAUST-AS NEEDED TO COMPLY W/TLV.
Protective Gloves:RUBBER-OIL RESISTANT GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:GLOVE RECOMMENDED IF PROLONGED SKIN CONTACT
    CANT BE AVOIDED
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING. REMOVE
    CONTAMINATED CLOTHING, LAUNDER OR DRY CLEAN.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

HCC:V6
Boiling Pt:B.P. Text:WIDE RANGE
Vapor Pres:<0.1
Vapor Density:>8
Spec Gravity:0.906 (H*2O=1)
Evaporation Rate &amp; Reference:<1 (BUTYL ACETATE=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:LIGHT AMBER LIQUID; PETROLEUM ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS SUCH AS LIQ CHLORINE, SODIUM, CALCIUM HYPOCHLORITE,
    PURE OXYGEN.
Stability Condition to Avoid:OPEN FLAMES, SPARKS, IGNITION SOURCES.
Hazardous Decomposition Products:CARBON MONOXIDE, HYDROGEN SULFIDE ON
    INCOMPLETE COMBUSTION.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSAL MUST BE I/A/W FEDERAL, STATE & LOCAL
    REGS . FOR LARGE QUANTITIES, ASSURE CONFORMITY W/APPLIC DISPOSAL
    REGS. DISPOSE OF ABSORBED MATL AT AN APPROVED WASTE DISPOSAL SITE
    OR FACILITY.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.